Download NCA-6.10 Exam Dumps Questions to get 100% Success in Nutanix [Q24-Q46]

Download NCA-6.10 Exam Dumps Questions to get 100% Success in Nutanix 

100% Accurate Answers! NCA-6.10 Actual Real Exam Questions

NEW QUESTION # 24
What is the recommended step before performing any upgrade procedure?

• A. Put the hosts into maintenance mode
• B. Run Nutanix Cluster Check
• C. Clear all alerts in Prism
• D. Put the CVMs into maintenance mode

Answer: B

Explanation:
The correct answer isB. Run Nutanix Cluster Check (NCC).
Before performingany upgrade procedure(AOS, Foundation, LCM, etc.), it is strongly recommended torun the Nutanix Cluster Check (NCC). This tool performs acomprehensive health assessmentof the cluster and validates its readiness for the upgrade, including:
* Disk integrity
* Network configuration
* CVM health
* Cluster services status
Prism UI Navigation Path:
Health > Run NCC Check (via Actions menu)
Command Line Alternative:
bash
CopyEdit
ncc health_checks run_all
Clarifications:
* A (Put hosts into maintenance mode): Not required before upgrades; LCM handles host management automatically.
* C (Put CVMs into maintenance mode): Not correct. CVMs must be operational during upgrades.
* D (Clear all alerts): Irrelevant unless the alerts indicate upgrade-blocking issues, which NCC identifies.
Official Reference:
* Nutanix Upgrade Guide - Pre-upgrade Checklist Section
* Excerpt: "It is strongly recommended to run NCC prior to starting the upgrade process to detect any cluster issues."

NEW QUESTION # 25
What minimum number of clusters must be registered to Prism Central to open a support case from the UI?

• A. 0
• B. 1
• C. 2
• D. 3

Answer: C

Explanation:
The correct answer isB. 1
Nutanix Prism Central provides the ability to create and manage support casesdirectly from the UI, but this functionality requiresat least one clusterto be registered to Prism Central. The Support option becomes active onceone or more clustersare managed.
Important distinctions:
* Zero clusters(Option A): With no clusters registered, Prism Central is effectively disconnected from any environment and thus cannot associate logs or telemetry with a support case.
* One cluster(Option B): Enables access to support features, including log bundle generation and direct case submission.
* Options C and D (2 or 3 clusters) are incorrect; they arenot a requirementfor enabling support case functionality.
Prism Central UI Navigation Path:
Settings (gear icon) > Support > Create Support Case
Official Reference:
* Nutanix Prism Central Guide - Support Integration Section
* Excerpt: "To open a support case through Prism Central, ensure at least one cluster is registered.
Support features become available once a cluster is connected."
Conclusion:Only one cluster is required to activate the support case workflow in Prism Central.

NEW QUESTION # 26
What priority case can be opened to guarantee a 8-hour response for a customer with Production Support?

• A. P2
• B. P1
• C. P3
• D. P4

Answer: B

Explanation:
APriority 1 (P1)case guarantees an8-hour response timefor customers with Production Support. P1 cases are designated for critical issues that severely impact business operations or cause a complete system outage, requiring immediate attention from Nutanix Support.
Other priorities:
* P2: High-impact issues but not critical, response time varies.
* P3: Medium impact, typically non-urgent issues.
* P4: Low priority, general inquiries or minor issues.
:
Nutanix Support SLA Documentation - Priority Levels.
Nutanix Production Support Details - Case Handling.

NEW QUESTION # 27
When creating a new storage container, what is the default configuration for Compression?

• A. Post-process (60 minutes)
• B. Inline
• C. Post-process (15 minutes)
• D. Disabled

Answer: D

Explanation:
The correct answer isB. Disabled.
When creating a new storage container in Prism Element or Prism Central,compression is disabled by default. The administrator mustexplicitly enableone of the available compression options:
* Inline Compression
* Post-process Compression
If no compression type is selected, the container remains uncompressed.
UI Navigation Path:
Storage > Storage Containers > Create Container > Compression Settings
Clarifications:
* A (60 mins)andC (15 mins): Not standard default post-process intervals.
* D (Inline): Must be manually selected.
Official Reference:
* Nutanix Storage Administration Guide - Creating and Configuring Containers
* Excerpt: "Compression is disabled by default during container creation. Admins must select inline or post-process if desired."

NEW QUESTION # 28
What is the minimum number of nodes required in a cluster for enabling Erasure Coding?

• A. 0
• B. 1
• C. 2
• D. 3

Answer: A

Explanation:
The correct answer isC. 4
Erasure Coding (EC-X)in Nutanix is a data efficiency feature that replaces multiple replicas with parity data to reduce storage overhead while still protecting against failures. Theminimum node requirementfor enabling Erasure Coding is4 nodes, due to the need to distribute data and parity across multiple failure domains.
Details:
* RF2 with EC-Xrequires at least4 nodes.
* RF3 with EC-Xrequiresat least 6 or 8 nodes, depending on configuration.
Prism UI Navigation Path:
Storage > Storage Containers > Enable EC-X
Official Reference:
* Nutanix Bible - Erasure Coding Section
* Nutanix Storage Admin Guide
* Excerpt: "A minimum of 4 nodes is required in a Nutanix cluster to enable Erasure Coding (EC-X) with RF2."

NEW QUESTION # 29
At what time does LCM auto-inventory run by default?

• A. 1:00am
• B. 4:00am
• C. 2:00am
• D. 3:00am

Answer: D

NEW QUESTION # 30

After logging into Prism Element, an administrator sees a red heart as shown in the exhibit.
Which dashboard will help the administrator isolate the cause of the issue?

• A. Health
• B. Tasks
• C. Alerts
• D. Analysis

Answer: C

Explanation:
In Nutanix Prism Element, thered heart iconat the top-right of the UI indicates that there is acritical alert affecting the cluster's health. This icon is part of theAlert Monitoring System, and clicking on it redirects the user to theAlerts dashboard, where all current active alerts-including their severity, source, and recommended remediation steps-are listed.
What to do:
* Navigate to theAlertssection.
* Review allcritical alertsfor further diagnosis.
* Cross-reference with theHealth dashboardif deeper system component checks are needed.
Clarification of Other Options:
* A. Health:Summarizes system component states but does not provide detailed alert causes.
* B. Tasks:Tracks user-initiated jobs, unrelated to fault diagnosis.
* D. Analysis:Used for performance metrics and trends, not fault alerts.
Prism UI Navigation Path:
Click the red heart icon # Alerts Dashboard
Official Reference:
* Nutanix Administration Guide - Alerts and Monitoring
* Excerpt: "A red heart icon in Prism indicates a critical alert. Use the Alerts dashboard to identify and resolve the issue."

NEW QUESTION # 31
Which option is supported by Nutanix for Data-at-Rest encryption?

• A. Software-only Encryption
• B. Cluster-only Encryption
• C. Storage Pool-only Encryption
• D. Data-only Encryption

Answer: A

Explanation:
The correct answer isD. Software-only Encryption.
Nutanix supportsData-at-Rest Encryption (DARE)through bothhardware-basedandsoftware-based methods. Among the supported solutions,software-only encryptionis a widely used and officially supported method, especially whenSelf-Encrypting Drives (SEDs)are not in use.
Key facts about Nutanix DARE:
* Enables encryption of data written to physical media.
* Works at theCVM and controller layer, ensuring all I/O is encrypted before being persisted.
* Software-based encryptioncan be enabled via Prism Central or command-line usingNative Key Management (NKM)orexternal KMIP-compliant key managers.
* Hardware encryption (SED)is optional and not required for DARE.
Clarifications:
* A. Storage Pool-only Encryption: Not valid; encryption applies at thecluster level, not only to storage pools.
* B. Data-only Encryption: Ambiguous and not a Nutanix-supported term.
* C. Cluster-only Encryption: Misleading; encryption is applied to data at rest, not to the "cluster" object.
Prism UI Navigation Path:
Settings > Security > Encryption
Official Reference:
* Nutanix Security Guide - Data-at-Rest Encryption
* Nutanix Bible - Encryption Section
* Excerpt: "Nutanix supports software-only data-at-rest encryption using Native Key Management or external KMIP key managers, without requiring self-encrypting drives."

NEW QUESTION # 32
An administrator wants to collect log files that have been requested by Nutanix Support.
From which Prism Element dashboard can this be accomplished?

• A. Health
• B. Alerts
• C. Settings
• D. Analysis

Answer: C

Explanation:
Log files requested by Nutanix Support can be collected from theSettingsdashboard in Prism Element. Within Settings, administrators can access the "Export Logs" or "Support" section to collect and upload diagnostic data directly to Nutanix Support.
* A. Settings:Correct, as logs are collected and uploaded via the Settings dashboard.
* B. Alerts:Incorrect, as Alerts display system issues but do not provide log collection options.
* C. Health:Incorrect, as the Health dashboard focuses on system checks and cluster status.
* D. Analysis:Incorrect, as the Analysis dashboard provides performance monitoring, not log collection.
References:
Nutanix Administration Guide: Collecting and Uploading Logs.
Nutanix Support KB Article on Log Collection in Prism

NEW QUESTION # 33
Nutanix Support has asked an administrator to provide an NCC output, but there is no access to the command line.
What should the administrator do to provide the requested NCC output?

• A. Run Health Checks in the Event Dashboard.
• B. Configure email in Alert Settings and Run Health Checks in the Health Dashboard.
• C. Configure email in Alert Settings and Run Health Checks in the Alert Dashboard.
• D. Run Health Checks in the Alert Dashboard and enter an email to send it to.

Answer: B

Explanation:
When command-line access is unavailable, Nutanix administrators can use the Prism UI to generate an NCC (Nutanix Cluster Check) output. The steps are:
* Configure the email settings inAlert Settingsunder the Prism UI.
* Navigate to theHealth Dashboard, where the "Run Health Checks" option can be used.
* Provide the administrator's email address to send the health report, which includes NCC outputs.
This method enables the administrator to share diagnostic information with Nutanix Support directly via email.
* A. Run Health Checks in the Alert Dashboard and enter an email to send it to:Incorrect. Health Checks are run from the Health Dashboard, not the Alert Dashboard.
* B. Configure email in Alert Settings and Run Health Checks in the Health Dashboard:Correct.
This provides the requested NCC output when the command-line is inaccessible.
* C. Run Health Checks in the Event Dashboard:Incorrect. Health Checks are not run from the Event Dashboard.
* D. Configure email in Alert Settings and Run Health Checks in the Alert Dashboard:Incorrect, as this is not the correct location for Health Checks.
References:
Nutanix Administration Guide: Health Dashboard and NCC.
Nutanix Support Knowledge Base Article on Sending NCC Reports Without CLI Access.

NEW QUESTION # 34
An administrator is conducting updates in a Nutanix cluster and is being prompted for handling non-migratable VMs.
Which VM type is non-migratable?

• A. VMs without NGT
• B. Memory Overcommitted
• C. VMs O VMs with attached Volume Groups
• D. VMs marked as an Agent

Answer: C

NEW QUESTION # 35
An administrator is considering a data protection strategy between two sites. There is a 10ms round trip latency between the two clusters. Which data protection solution can the administrator implement that minimizes data loss in the event of a disaster?

• A. Async DR
• B. NearSync Replication
• C. Metro Availability
• D. Synchronous Replication

Answer: B

Explanation:
The correct answer isA. NearSync Replication.
Key Concepts from Official Nutanix Documentation:
Nutanix supports various types of data replication methods depending on the Recovery Point Objective (RPO), Recovery Time Objective (RTO), and the latency between the sites.
* Metro Availabilityrequires a maximum latency of<5ms RTTand is used forzero RPO synchronous replication. Since the given latency is 10ms,Metro Availability is not supportedin this case.
Reference: Nutanix Bible - Metro Availability Section
Prism UI Navigation: Protection Domains > Metro Availability
Synchronous Replicationis often synonymous withMetro Availabilityin Nutanix's implementation. Thus, it is similarly bound by the <5ms RTT requirement.
Async DR (Asynchronous Disaster Recovery)allows for more relaxed RPOs, typically1 hour or more, which doesnot minimize data lossin the event of a disaster.
NearSync Replicationsupports anRPO as low as 1 minuteand issuitable for up to 20ms RTT latency. It utilizeslightweight snapshotsandschedule-based replicationto deliverlow-RPO protectioneven over relatively long distances and moderate latencies.
Reference: Nutanix Data Protection Guide - NearSync Overview
Prism UI Navigation: Data Protection > Protection Domains > Schedule (with 1-minute RPO option) Detailed Source References:
Nutanix Data Protection and DR Guide - v5.x and later:"NearSync replication enables you to achieve RPOs as low as 1 minute and is designed to work with round-trip latencies of up to 20ms." Prism Central UI:Navigate toProtection > Data Protection > Protection Domains > Create Schedule# Set schedule type to "NearSync" and observe the 1-minute RPO options.
Hence, since 10ms RTTexceeds Metro Availability requirementsbut iswell within NearSync's acceptable latency, the best choice thatminimizes data lossis:

NEW QUESTION # 36
An administrator has spent time correcting specific issues that have been identified by NCC Health Checks in Prism Element.
How can just the checks that previously did not pass be executed again to confirm they are all resolved?

• A. Run ncc health checks run_all.
• B. Select Only Failed And Warning Checks.
• C. Run LCM Pre-Upgrade to trigger NCC Checks.
• D. Select Run Check for each check worked.

Answer: B

Explanation:
To rerun only the health checks that previously failed or issued warnings, the administrator can select theOnly Failed and Warning Checksoption in Prism Element. This targeted approach helps verify that resolved issues have been addressed without rerunning all checks unnecessarily.
Steps:
* Navigate toPrism Element > Health > NCC Checks.
* Filter forOnly Failed and Warning Checksand rerun them.
Other options:
* A. Run LCM Pre-Upgrade: Runs pre-upgrade checks, not related to health check validation.
* B. Runncc health_checks run_all: Executes all checks, not just failed ones.
* C. Select Run Check for each check worked: Requires manual execution for each check.
References:
Nutanix Administration Guide - Health Checks.
Nutanix Cluster Check (NCC) Documentation.

NEW QUESTION # 37
An administrator has been directed to ensure that all Prism Element and Prism Central clusters allow Nutanix Support to gather logs without needing engagement.
What should the administrator enable to meet this requirement?

• A. Self-Service
• B. Pulse
• C. Proxy Server
• D. NKP

Answer: A

NEW QUESTION # 38
An administrator wants to collect log files that have been requested by Nutanix Support.
From which Prism Element dashboard can this be accomplished?

• A. Health
• B. Alerts
• C. Settings
• D. Analysis

Answer: A

NEW QUESTION # 39
An administrator is performing AHV upgrades on an 8-node cluster configured with Redundancy Factor 3.
How many nodes would be placed into maintenance mode simultaneously?

• A. 0
• B. 1
• C. 2
• D. 3

Answer: C

Explanation:
In a cluster configured with Redundancy Factor 3 (RF3), the system ensures that data is replicated across at least three nodes to tolerate the failure of two nodes. During an AHV upgrade, Nutanix only placesone node at a timeinto maintenance mode, even in an RF3 configuration, to minimize the impact on data redundancy and cluster operations.
* A. 1:Correct, as AHV upgrades proceed node by node in RF3.
* B. 2, C. 3, D. 4:These options are incorrect, as only one node is upgraded at a time regardless of RF3.
References:
Nutanix AOS Upgrade Guide.
Nutanix Support KB Article on RF3 Behavior and Maintenance.

NEW QUESTION # 40
Which bridge does the Controller VM use by default to communicate with the AHV host it runs on?

• A. bridge0
• B. virbro
• C. bro
• D. vs0

Answer: A

NEW QUESTION # 41
An administrator has been directed to ensure that all Prism Element and Prism Central clusters allow Nutanix Support to gather logs without needing engagement.
What should the administrator enable to meet this requirement?

• A. Self-Service
• B. Pulse
• C. Proxy Server
• D. NKP

Answer: B

Explanation:
To allow Nutanix Support to gather logs automatically without requiring manual intervention, the administrator should enablePulse. Pulse is a telemetry service that collects and sends system health, log, and usage data to Nutanix Support securely.
Steps:
* Navigate toPrism Central > Settings > Pulse.
* Enable the service and configure as required for your environment.
Other options:
* Self-Service: Refers to role-based access for users, unrelated to log collection.
* Proxy Server: Used for network communication, not log gathering.
* NKP: Refers to Nutanix Cluster Protocol, unrelated to telemetry.
:
Nutanix Administration Guide - Pulse Configuration.
Nutanix Support Portal - Pulse Service Details.

NEW QUESTION # 42
What is the purpose of the OpLog?

• A. Dynamic read cache
• B. Persistent data storage
• C. Persistent write buffer
• D. Global metadata

Answer: C

Explanation:
The OpLog (Operational Log) in Nutanix serves as apersistent write bufferfor incoming I/O operations. It temporarily stores write requests to ensure fast acknowledgment to clients and better performance. The data is later coalesced and written to the Extent Store for long-term storage.
* A. Persistent write buffer:Correct, as the OpLog optimizes write performance by buffering writes temporarily.
* B. Persistent data storage:Incorrect, as this describes the Extent Store, not the OpLog.
* C. Global metadata:Incorrect, as metadata operations are handled by the Metadata Store.
* D. Dynamic read cache:Incorrect, as read caching is managed separately, often involving SSD-based caches.
References:
Nutanix Bible: Explanation of OpLog and Extent Store.
Nutanix University: NCP Certification Study Materials.

NEW QUESTION # 43
What priority case can be opened to guarantee a 8-hour response for a customer with Production Support?

• A. P2
• B. P1
• C. P3
• D. P4

Answer: B

NEW QUESTION # 44
In Prism Element, to which object are policies such as replication factor and storage efficiency settings applied?

• A. Storage Pool
• B. Virtual Machine
• C. vBlock
• D. Container

Answer: D

Explanation:
In Prism Element, policies such as replication factor and storage efficiency settings are applied to Containers. A container is a logical grouping of one or more storage pools and defines the storage resources available to virtual machines. By applying policies to a container, you can set the replication factor, storage efficiency settings, and other storage-related settings for all of the virtual machines that are associated with that container. This is a fundamental concept in Nutanix Platform.

NEW QUESTION # 45
An administrator needs to create a VM Template from an existing VM.
What is required for this action to be successful?

• A. The VM is powered off.
• B. Sysprep or Cloud-init script.
• C. Windows OS is installed.
• D. The VM is powered on.

Answer: A

Explanation:
To create a VM template from an existing VM in Nutanix, the VM must be powered off. This ensures that the template is consistent and does not include any transient data or activity from the VM. Once the VM is powered off, the administrator can use the Prism UI to take a snapshot and designate it as a template.
* A. Sysprep or Cloud-init script:These are optional for post-deployment configuration, not mandatory for creating a template.
* B. The VM is powered on:This is incorrect, as the VM must be powered off.
* C. Windows OS is installed:The OS type is irrelevant for creating a template.
* D. The VM is powered off:Correct, as creating a template requires the VM to be in a powered-off state.
References:
Nutanix AHV Administration Guide: Nutanix Documentation
Nutanix University Certification Content for NCP and NCM.

NEW QUESTION # 46
......

Best Value Available! Realistic Verified Free NCA-6.10 Exam Questions: https://www.latestcram.com/NCA-6.10-exam-cram-questions.html

Pass Your Exam Easily! NCA-6.10 Real Question Answers Updated: https://drive.google.com/open?id=17y1gnxlXNNBov1m_QAM0iiYpBNeAAZeR